Proxmark3 community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

Announcement

Time changes and with it the technology
Proxmark3 @ discord

Users of this forum, please be aware that information stored on this site is not private.

#1 2013-01-30 14:09:15

zbee
Member
Registered: 2013-01-30
Posts: 8

Indala Card cloning issue, please help:)

Hi,
I am a newbie to the Proxmark3 forum.
In the past I have been learning many new things from the forum, this is my first posting, as I am having some issues now with cloning two cards. The first is with an Indala card and the second issue is with an unknown card which I narrowed down to being an LF card but I will post that issues somewhere else.

I have tried to clone a Indala Clamshell Card, It has the "indala" imprinted on the bottom back of the card (only Indala card I have access to).

I have included a screen shot of what I have tried.

http://www.flickr.com/photos/92735970@N03/8428798467/

I originally thought I could get the ID number from using:
"lf hid fskdemod"
Which I would get 9 number:
#db# TAG ID: 000000003 (1)
From my understanding if it was a correct TAG ID you will be given 10 numbers.
(Before I knew this I cloned a T5577 with the above number, which failed to work, no real surprise.)

Question 1: Dose it mean anything if you are able to get a TAG ID with 9 numbers, as I found if I placed different cards apart from HID and this Indala card there will be no TAG ID number shown?

I tried using:
"lf indalademod" but got this reply,

Expecting a bit less then 0 rae bits
Recovered 0 raw bits
worst metric (0=best...7=worest): 0 at pos 0
Warning: not enough raw bits to get a full UID
Partial UID=N

Q2:What might I be doing wrong?
Q3:What should I be doing or which commands should I used so I am able to find the UID or ID?
Q4:Might the card be encrypted thus the above results & I will be unable to clone the card?

Thank you for looking and any advice would be most welcome.
If I am missing any information to help find a solution please feel free to ask.

Cheers

Offline

#2 2013-01-30 15:24:45

elliot42
Contributor
From: Australia
Registered: 2013-01-11
Posts: 16

Re: Indala Card cloning issue, please help:)

I successfully read the UID from my Indala card with the following commands:
lf read
data samples 2000
lf indalademod

Then I was able to clone it to a T5557 with:
lf indalaclone <UID in hex>

I've been using the cloned tag at work (it's for access to the office) for the past week with no problems.
I also cloned my carpark pass which is a HID card using "lf hid fskdemod" then "lf hid clone <UID>".

Offline

#3 2013-01-30 15:44:17

zbee
Member
Registered: 2013-01-30
Posts: 8

Re: Indala Card cloning issue, please help:)

Many thanks elliot42!

I found the proxmark3 to be an excellent tool, the drawback is knowing the right commands.
Will let you know how I go as it is for a friend which also uses it for the office.

I have clones the HID for my apartment without issues but thank you for the commands
Will let you know how I go.

Offline

#4 2013-02-02 08:56:51

zbee
Member
Registered: 2013-01-30
Posts: 8

Re: Indala Card cloning issue, please help:)

The commands worked perfectly, thanks mate

Offline

Board footer

Powered by FluxBB