Proxmark3 developers community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

#1 2010-08-14 15:02:12

kramxorpprompet
Member
Registered: 2010-07-15
Posts: 5

How to use JTAG to upgrade a proxmark

Hello, it's been days since I first started trying to flash a proxmark, but I really can't figure it out.

I bought a JTAG connector (an Olimex USB TINY)... but I can't connect it through openocd on my backtrack.

I compiled openocd for libftdi with

./configure --enable-ft2232_libftdi && make && make install

Here is the configuration file that i used for openocd (0.4.0 version)

# cat ~/openocd.cfg
source [find interface/olimex-jtag-tiny.cfg]
source [find target/sam7x256.cfg]

telnet_port 4444
#

Then i connect both the proxmark and the olimex, and when i start openocd here's what i get:

# openocd -f ~/openocd.cfg
Open On-Chip Debugger 0.4.0 (2010-08-12-11:08)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.berlios.de/doc/doxygen/bugs.html
srst_only srst_pulls_trst srst_gates_jtag srst_open_drain
Info : clock speed 6000 kHz
Info : JTAG tap: sam7x256.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3)
Warn : Unexpected idcode after end of chain: 32 0x00000000
Warn : Unexpected idcode after end of chain: 64 0x00000000
Warn : Unexpected idcode after end of chain: 96 0x00000000
Warn : Unexpected idcode after end of chain: 128 0x00000000
Warn : Unexpected idcode after end of chain: 160 0x00000000
Warn : Unexpected idcode after end of chain: 192 0x00000000
Warn : Unexpected idcode after end of chain: 224 0x00000000
Warn : Unexpected idcode after end of chain: 256 0x00000000
Warn : Unexpected idcode after end of chain: 288 0x00000000
Warn : Unexpected idcode after end of chain: 320 0x00000000
Warn : Unexpected idcode after end of chain: 352 0x00000000
Warn : Unexpected idcode after end of chain: 384 0x00000000
Warn : Unexpected idcode after end of chain: 416 0x00000000
Warn : Unexpected idcode after end of chain: 448 0x00000000
Warn : Unexpected idcode after end of chain: 480 0x00000000
Warn : Unexpected idcode after end of chain: 512 0x00000000
Warn : Unexpected idcode after end of chain: 544 0x00000000
Warn : Unexpected idcode after end of chain: 576 0x00000000
Warn : Unexpected idcode after end of chain: 608 0x00000000
Error: double-check your JTAG setup (interface, speed, missing TAPs, ...)
Info : JTAG tap: sam7x256.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3)
Warn : Unexpected idcode after end of chain: 32 0x00000000
Warn : Unexpected idcode after end of chain: 64 0x00000000
Warn : Unexpected idcode after end of chain: 96 0x00000000
Warn : Unexpected idcode after end of chain: 128 0x00000000
Warn : Unexpected idcode after end of chain: 160 0x00000000
Warn : Unexpected idcode after end of chain: 192 0x00000000
Warn : Unexpected idcode after end of chain: 224 0x00000000
Warn : Unexpected idcode after end of chain: 256 0x00000000
Warn : Unexpected idcode after end of chain: 288 0x00000000
Warn : Unexpected idcode after end of chain: 320 0x00000000
Warn : Unexpected idcode after end of chain: 352 0x00000000
Warn : Unexpected idcode after end of chain: 384 0x00000000
Warn : Unexpected idcode after end of chain: 416 0x00000000
Warn : Unexpected idcode after end of chain: 448 0x00000000
Warn : Unexpected idcode after end of chain: 480 0x00000000
Warn : Unexpected idcode after end of chain: 512 0x00000000
Warn : Unexpected idcode after end of chain: 544 0x00000000
Warn : Unexpected idcode after end of chain: 576 0x00000000
Warn : Unexpected idcode after end of chain: 608 0x00000000
Error: double-check your JTAG setup (interface, speed, missing TAPs, ...)
Command handler execution failed
Warn : jtag initialization failed; try 'jtag init' again.
^C

I also tested openocd with ftd2xx (instead of libftdi) and the results are the same:

# openocd -f ~/openocd.cfg
Open On-Chip Debugger 0.4.0 (2010-08-12-18:34)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.berlios.de/doc/doxygen/bugs.html
srst_only srst_pulls_trst srst_gates_jtag srst_open_drain
Info : device: 4 "2232C"
Info : deviceID: 364511236
Info : SerialNumber: ��@
Info : Description: Olimex OpenOCD JTAG TINY A
Info : clock speed 6000 kHz
Info : JTAG tap: sam7x256.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3)
Warn : Unexpected idcode after end of chain: 32 0x00000000
Warn : Unexpected idcode after end of chain: 64 0x00000000
Warn : Unexpected idcode after end of chain: 96 0x00000000
Warn : Unexpected idcode after end of chain: 128 0x00000000
Warn : Unexpected idcode after end of chain: 160 0x00000000
Warn : Unexpected idcode after end of chain: 192 0x00000000
Warn : Unexpected idcode after end of chain: 224 0x00000000
Warn : Unexpected idcode after end of chain: 256 0x00000000
Warn : Unexpected idcode after end of chain: 288 0x00000000
Warn : Unexpected idcode after end of chain: 320 0x00000000
Warn : Unexpected idcode after end of chain: 352 0x00000000
Warn : Unexpected idcode after end of chain: 384 0x00000000
Warn : Unexpected idcode after end of chain: 416 0x00000000
Warn : Unexpected idcode after end of chain: 448 0x00000000
Warn : Unexpected idcode after end of chain: 480 0x00000000
Warn : Unexpected idcode after end of chain: 512 0x00000000
Warn : Unexpected idcode after end of chain: 544 0x00000000
Warn : Unexpected idcode after end of chain: 576 0x00000000
Warn : Unexpected idcode after end of chain: 608 0x00000000
Error: double-check your JTAG setup (interface, speed, missing TAPs, ...)
Info : JTAG tap: sam7x256.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3)
Warn : Unexpected idcode after end of chain: 32 0x00000000
Warn : Unexpected idcode after end of chain: 64 0x00000000
Warn : Unexpected idcode after end of chain: 96 0x00000000
Warn : Unexpected idcode after end of chain: 128 0x00000000
Warn : Unexpected idcode after end of chain: 160 0x00000000
Warn : Unexpected idcode after end of chain: 192 0x00000000
Warn : Unexpected idcode after end of chain: 224 0x00000000
Warn : Unexpected idcode after end of chain: 256 0x00000000
Warn : Unexpected idcode after end of chain: 288 0x00000000
Warn : Unexpected idcode after end of chain: 320 0x00000000
Warn : Unexpected idcode after end of chain: 352 0x00000000
Warn : Unexpected idcode after end of chain: 384 0x00000000
Warn : Unexpected idcode after end of chain: 416 0x00000000
Warn : Unexpected idcode after end of chain: 448 0x00000000
Warn : Unexpected idcode after end of chain: 480 0x00000000
Warn : Unexpected idcode after end of chain: 512 0x00000000
Warn : Unexpected idcode after end of chain: 544 0x00000000
Warn : Unexpected idcode after end of chain: 576 0x00000000
Warn : Unexpected idcode after end of chain: 608 0x00000000
Error: double-check your JTAG setup (interface, speed, missing TAPs, ...)
Command handler execution failed
Warn : jtag initialization failed; try 'jtag init' again.
^C

Other than those unexpected idcodes, another odd thing that I notice is the SerialNumber which has some strange characters in it (this looks like a non allocated buffer since every time I restart openocd the characters inside the SerialNumber are different)... Anyway... I still i don't know what to do.

Could it be useful, I have the same identical results with jtag_khz 6000, jtag_khz 3000 and jtag_khz 300

The proxmark3 and the olimex are connected through an usb1 hub (I even tested this on a old notebook that only has usb1, with Windows XP SP3 and libusb-win32, and I got the same exact results).

Any ideas please?

Thanks

Offline

#2 2010-08-23 22:12:02

kramxorpprompet
Member
Registered: 2010-07-15
Posts: 5

Re: How to use JTAG to upgrade a proxmark

bump

Offline

Board footer

Powered by FluxBB