Proxmark3 community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

Announcement

Time changes and with it the technology
Proxmark3 @ discord

Users of this forum, please be aware that information stored on this site is not private.

#1 2019-08-13 20:35:27

l07tb0y
Contributor
Registered: 2019-08-12
Posts: 9

I am new so please go easy on me :) need help cloning a DataWatch card

I have the following
1. Data Watch RFID Tag
2. PROXMARK3D v4.01 Flashed to the latest firmware
3. Battery and Bluetooth pack installed

trying to read the Datawatch card into the Memory of the Proxmark and see if I can get a reader to recognize the Proxmark as the card.

When I was buying this setup I was told it should be press the button to turn the card into a reader and record the card into a memory bank and than press it again for it to become a tag reading these forums I guess that is not true smile

So is there a basic getting started guide or video? I can make a guide if someone is willing to help me get it going.

 [ Proxmark3 RFID instrument ] 
          

 [ CLIENT ]          
  client: RRG/Iceman          
  compiled with Clang/LLVM 4.2.1 Compatible Apple LLVM 10.0.1 (clang-1001.0.46.4)          

 [ PROXMARK RDV4 ]          
  external flash:                  present           
  smartcard reader:                present           

 [ PROXMARK RDV4 Extras ]          
  FPC USART for BT add-on support: absent           
          
 [ ARM ]
  bootrom: RRG/Iceman/master/47b60d8 2019-08-11 21:49:19
       os: RRG/Iceman/master/47b60d8 2019-08-11 21:49:32
  compiled with GCC 5.4.1 20160919 (release) [ARM/embedded-5-branch revision 240496]

 [ FPGA ]
  LF image built for 2s30vq100 on 2019/ 7/31 at 15:57:16
  HF image built for 2s30vq100 on 2018/ 9/ 3 at 21:40:23          

 [ Hardware ]           
  --= uC: AT91SAM7S512 Rev B          
  --= Embedded Processor: ARM7TDMI          
  --= Nonvolatile Program Memory Size: 512K bytes, Used: 271172 bytes (52%) Free: 253116 bytes (48%)          
  --= Second Nonvolatile Program Memory Size: None          
  --= Internal SRAM Size: 64K bytes          
  --= Architecture Identifier: AT91SAM7Sxx Series          
  --= Nonvolatile Program Memory Type: Embedded Flash Memory          
[usb] pm3 --> hw tune
          
[=] Measuring antenna characteristics, please wait...
          
..
          
[+] LF antenna: 67.55 V - 125.00 kHz          
[+] LF antenna: 51.55 V - 134.00 kHz          
[+] LF optimal: 76.90 V - 127.66 kHz          
[+] LF antenna is OK  
          
[+] HF antenna: 49.43 V - 13.56 MHz          
[+] HF antenna is OK           
          
[+] Displaying LF tuning graph. Divisor 89 is 134kHz, 95 is 125kHz.
          
[usb] pm3 --> 

Offline

#2 2019-08-13 20:50:46

l07tb0y
Contributor
Registered: 2019-08-12
Posts: 9

Re: I am new so please go easy on me :) need help cloning a DataWatch card

Ok so just for good measure I tried the button while it was attached to the PC and held it for 4-5 seconds and it starting recording I put the DataWatch card close to the reader and got the following

#db# [=] starting recording          
#db# DEBUG: (preambleSearchEx) preamble found at 52          
#db# DEBUG: (preambleSearchEx) preamble 2 found at 148          
#db# TAG ID: 2401ba4460 (8752) - Format Len: 34bit - FC: 221 - Card: 8752          
#db# Stopped          
#db# [=] recorded bank 1 | 24 01ba4460  

than I pressed the button again and it went into playing

#db# [=] playing          
#db# [=] 1 24 01ba4460  

and low and behold I was able to get the reader to recognize the Proxmark and work that is very neat.

Now I have to figure out how to put something in memory bank 2 that is a Indala card.

Offline

#3 2019-08-14 01:25:24

iceman
Administrator
Registered: 2013-04-25
Posts: 9,497
Website

Re: I am new so please go easy on me :) need help cloning a DataWatch card

What you are refering as "press the button to turn the card into a reader and record the card into a memory bank"  is what we call a standalone mode. You would need to figure out how standalone mode works. 

Since you are new, I suggest you spend some serious time reading all docs over at the RRG/Iceman repo in order to take full advantage of your new RDV4 w Blueshark.

https://github.com/RfidResearchGroup/pr … alone-mode

Offline

#4 2019-08-14 19:10:26

l07tb0y
Contributor
Registered: 2019-08-12
Posts: 9

Re: I am new so please go easy on me :) need help cloning a DataWatch card

Looks like all the directions are old so i made an updated diagram of LEDs and how they work on my ProxMark

jDudMNz.jpg

Last edited by l07tb0y (2019-08-14 19:16:02)

Offline

#5 2019-08-14 21:23:41

iceman
Administrator
Registered: 2013-04-25
Posts: 9,497
Website

Re: I am new so please go easy on me :) need help cloning a DataWatch card

Great...
However the leds on samy_run  needs to be made.   Because as of now, they suck

Offline

Board footer

Powered by FluxBB