Proxmark3 community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

You are not logged in.

Announcement

Time changes and with it the technology
Proxmark3 @ discord

Users of this forum, please be aware that information stored on this site is not private.

#1 2018-12-04 12:34:55

Gtpy
Contributor
From: GER
Registered: 2017-10-24
Posts: 32

[RDV4] db unknown command: 0xd22d410d

Hi,

I am new to the topic Proxmark3.
What does the following message mean? This message appears from time to time when starting the client.
After exiting and restarting the client, it usually disappears.

#db# unknown command:: 0xd22d410d       

Proxmark RDV4

pm3 --> hw version

Proxmark3 RFID instrument
          

 [ CLIENT ]          
 client: iceman build for RDV40 with flashmem; smartcard;  

 [ ARM ]
 bootrom: iceman/master/259dbadb 2018-12-02 10:56:33
      os: iceman/master/259dbadb 2018-12-02 10:56:36

 [ FPGA ]
 LF image built for 2s30vq100 on 2018/ 9/ 8 at 13:57:51
 HF image built for 2s30vq100 on 2018/ 9/ 3 at 21:40:23          

 [ Hardware ]           
  --= uC: AT91SAM7S512 Rev A          
  --= Embedded Processor: ARM7TDMI          
  --= Nonvolatile Program Memory Size: 512K bytes, Used: 241920 bytes (46%) Free: 282368 bytes (54%)          
  --= Second Nonvolatile Program Memory Size: None          
  --= Internal SRAM Size: 64K bytes          
  --= Architecture Identifier: AT91SAM7Sxx Series          
  --= Nonvolatile Program Memory Type: Embedded Flash Memory          



pm3 --> hw status
#db# Memory          
#db#   BIGBUF_SIZE.............40000          
#db#   Available memory........40000          
#db# Tracing          
#db#   tracing ................1          
#db#   traceLen ...............0          
#db# Currently loaded FPGA image          
#db#   mode.................... HF image built for 2s30vq100 on 2018/ 9/ 3 at 21:40:23          
#db# Flash memory          
#db#   Baudrate................24MHz          
#db#   Init....................OK          
#db#   Memory size.............2 mbits / 256kb          
#db#   Unique ID...............0xd567a882a70f7f26          
#db# Smart card module (ISO 7816)          
#db#   version.................v2.06          
#db# LF Sampling config          
#db#   [q] divisor.............95 (125 KHz)          
#db#   (b) bps.................8          
#db#   [d] decimation..........1          
#db#   [a] averaging...........Yes          
#db#   [t] trigger threshold...0          
#db# LF T55XX config          
#db#   [a] startgap............29*8 (232)          
#db#   (b) writegap............17*8 (136)          
#db#   [c] write_0.............15*8 (120)          
#db#   [d] write_1.............47*8 (376)          
#db#   [e] readgap.............15*8 (120)          
#db# USB Speed          
#db#   Sending USB packets to client...          
#db#   Time elapsed............1500ms          
#db#   Bytes transferred.......811520          
#db#   USB Transfer Speed PM3 -> Client = 541013 Bytes/s          
#db# Various          
#db#   MF_DBGLEVEL.............1          
#db#   ToSendMax...............-1          
#db#   ToSendBit...............0          
#db#   ToSend BUFFERSIZE.......2308          
#db# Installed StandAlone Mode          
#db#    LF HID26 standalone - aka SamyRun (Samy Kamkar)     

pm3 --> hw tune
          
[=] measuring antenna characteristics, please wait...
          
....
          
[+] LF antenna: 73,08 V - 125.00 kHz          
[+] LF antenna: 39,23 V - 134.00 kHz          
[+] LF optimal: 73,08 V - 125,00 kHz          
[+] LF antenna is OK  
          
[+] HF antenna: 48,15 V - 13.56 MHz          
[+] HF antenna is OK           
          
[+] Displaying LF tuning graph. Divisor 89 is 134khz, 95 is 125khz.

Thank you for your explanations.

Last edited by Gtpy (2018-12-04 21:23:43)

Offline

#2 2018-12-04 12:51:44

iceman
Administrator
Registered: 2013-04-25
Posts: 9,497
Website

Re: [RDV4] db unknown command: 0xd22d410d

Do you use the client from the compiled version  as your flashed firmware?

Offline

#3 2018-12-04 12:52:01

iceman
Administrator
Registered: 2013-04-25
Posts: 9,497
Website

Re: [RDV4] db unknown command: 0xd22d410d

And enjoy your new RDV40!

Offline

#4 2018-12-04 13:53:28

Gtpy
Contributor
From: GER
Registered: 2017-10-24
Posts: 32

Re: [RDV4] db unknown command: 0xd22d410d

Recompiled, flashed again.
Now it looks fine.

Some problems with lf search and the T5577 card which was in the package.
But try again later and if it's needed I open a new topic.

Thanks. like the new RDV4 - great work.

Offline

#5 2018-12-04 21:26:38

Gtpy
Contributor
From: GER
Registered: 2017-10-24
Posts: 32

Re: [RDV4] db unknown command: 0xd22d410d

Ok I tested it again.
It appears every time when I first connect the PM3 RDV4.
Now the message #db# unknown command:: 0xd32d410d

Then I exit the client.
After that, this message disappeared.

Offline

#6 2018-12-04 21:46:57

iceman
Administrator
Registered: 2013-04-25
Posts: 9,497
Website

Re: [RDV4] db unknown command: 0xd22d410d

hm...  Open a issue on Github and fill in the details of OS etc,   maybe a screen shot and lets see if others have this issue aswell

Offline

#7 2018-12-04 22:43:58

Gtpy
Contributor
From: GER
Registered: 2017-10-24
Posts: 32

Re: [RDV4] db unknown command: 0xd22d410d

iceman wrote:

hm...  Open a issue on Github and fill in the details of OS etc,   maybe a screen shot and lets see if others have this issue aswell

Issue is created: https://github.com/RfidResearchGroup/pr … /issues/66

Offline

Board footer

Powered by FluxBB